QCAD.org Forum

Posted: **Fri May 17, 2019 10:37 am**

Hello.
　
When I used dwg2pdf, I confirmed the following problem

・Command

/Applications/QCAD-Pro.app/Contents/Resources/dwg2pdf -l -a -n -fs standard Arial -paper=A3 -outfile=out.pdf sample.dxf.sjis.dxf

・Terminal

Code: Select all

18:32:10: Debug:    RDwgPlugin::init
18:32:10: Debug:    RDxfPlugin::init
18:32:10: Debug:    RHelpPlugin::init
18:32:10: Debug:    RPolygonPlugin::init
18:32:10: Debug:    RProScriptsPlugin::init
18:32:10: Debug:    RScriptsPlugin::init
18:32:10: Debug:    RSpatialIndexProPlugin::init
18:32:10: Debug:    RTriangulationPlugin::init
18:32:10: Debug:    calling odInitialize
18:32:10: Debug:    dropped global XDATA (no res buf):  "ViewportCenter"
/Applications/QCAD-Pro.app/Contents/Resources/qcad: line 18: 32033 Segmentation fault: 11  DYLD_LIBRARY_PATH="$DIR" "$binary" "$@"

　

According to the examination, it is generated when “±” is used in SJIS DXF file, and R21 or higher DXF format.
It did not occur in UTF-8.But, UTF-8 can not be used because it is garbled...

I have attached the file in question.Please confirm.

Thank you.

Posted: **Fri May 17, 2019 2:51 pm**

As far as I can tell, the attached file does not contain "±" but the characters 0x81 (not printable) and a "}", the latter which is causing the crash:
"}" is ending a formatting group without previously starting a formatting group with "{".

The crash will be fixed for the next release, but the text will not show anything as 0x81 is not a printable character and "}" is part of the formatting. Do you have a more complete example with more context?

Posted: **Sun May 19, 2019 9:31 am**

Hi Andrew.

Thank you for reply.

>The crash will be fixed for the next release,
Thank you. We look forward to waiting

>Do you have a more complete example with more context?
I'm sorry. Since this occurred on the client's file, There is no file that can be attached.

So,I will add the methods and results I have investigated.

1:It worked when the problem file was changed from sjis to utf8.
　(※ I have attached. "sample.dxf.utf8.dxf")

2:This problem was confirmed as follows.

[Original file]
ACADVER : AC1015
File character code : sjis
-> File Open and Convert(dwg2pdf) Success.

[Until the problem file is created.]
1.Open Original file with QCAD
2.Select format and save -> select over R21 -> output dxf File(UTF8) -> File Open and Convert(dwg2pdf) Success.
3.Change the dxf file (utf8) output in step 2 to sjis with a text editor or PHP. -> Crash.

[How to investigate the problem area]
1.Investigate the problem while erasing the entities one by one.
2.The content of the last entity is "± 1.0"
3.Execute 2 patterns leaving only "±" or "1.0".
"1.0" -> File Open and Convert(dwg2pdf) Success.
"±" -> Crash

I hope this information helps.
thank you.

Posted: **Mon May 20, 2019 5:10 am**

It is additional information.

>the attached file does not contain "±" but the characters 0x81 (not printable) and a "}", the latter which is causing the crash:

SJIS：± 　→ Open with UTF8：?}

[check tool]
https://tools.m-bsys.com/development_to ... uption.php

thank you.

QCAD.org Forum

[Mac]dwg2pdf Qcad Crash And "Segmentation fault: 11" Error.

[Mac]dwg2pdf Qcad Crash And "Segmentation fault: 11" Error.

Re: [Mac]dwg2pdf Qcad Crash And "Segmentation fault: 11" Error.

Re: [Mac]dwg2pdf Qcad Crash And "Segmentation fault: 11" Error.

Re: [Mac]dwg2pdf Qcad Crash And "Segmentation fault: 11" Error.