QCAD.org Forum

BARBWIRE Hatch Pattern, Handy for Architechs Adding Wire to Fences

WIRE-FENCE Hatch Pattern

An example of the previous Hatch Patterns in use...fill borders on Layer Invisible ...

LOOPLINKS Hatch Pattern..This Pattern Has been Removed and Will be updated ASAP
New Updated Pattern now on Page 4 of this topic

Hi Andrew
I noticed in Qcad 3.24 that small lines are rendered as points, this is good but I had to redo LATTICE-02.PAT
manually as it had a Zero on the end of 2 lines, I've commented in PAT files where... if the current Pattern
File is Exploded it shows these points and sometimes even if not exploded also shows them slightly.... anyway
here are the updated Files please just write over the older ones..see what I mean by points in image below..

Hi All

I'm Currently Testing out this tool "Tile2Hatch tool © CVH 2020" It seems to work flawlessly even at testing stage so
I'm posting all my patterns now using this tool as the AutoCad one has a lot of limitations... all header files will
contain this message to credit CVH on his amazing work on this tool that runs in Qcad
*HATCHNAME
;By John Hyslop, Tile2Hatch tool © CVH 2020
;Developed in inch as imperial QCAD3 pattern
AND
*HATCHNAME
;By John Hyslop, Tile2Hatch tool © CVH 2020
;Developed in mm as metric QCAD3 pattern

Files Attached In Imperial and Metric
BUBBLES-01,BUBBLES-02, LEAF-01 and LEAF-02..
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"
New Updated Patterns now on Page 4 of this topic

HATCH-DOTS and HATCH-SQRS in Metric and Imperial
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"

Optimised Patterns Please replace older patterns with these ones
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"

Patterns Will be updated ASAP

SCAFFOLD PATTERN HAS BEEN UPDATED, PLEASE SEE POST DATED 11/01/20
SQUIGGLE-01 & SQUIGGLE-02 Have been updated and can be found on page 4 of this topic

LEAF-03 PATTERN
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"
Pattern Will be updated ASAP
New Updated Pattern now on Page 4 of this topic

LATTICE-07 Pattern [ Similar to LATTICE-02, but woven instead of overlapped ]
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"
.
You Can Also Create This With My Free Basic Hatch Tool, That Can Be Downloaded Using The Link Below..
.
https://www.qcad.org/rsforum/viewtopic. ... =15#p33566
.

WEAVING Pattern
Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"
WARNING This uses a lot of resources use wisely

Pattern Will be updated ASAP
New Updated Pattern now on Page 4 of this topic

UPDATE TO SCAFFOLD PATTERN
DUPLICATE LINE REMOVED - 11-01-20

Using Tool Developed by CVH "Tile2Hatch tool © CVH 2020"

Hi All
As you are all aware CVH discovered that some hatch patterns when hatched far away from the drawings X Y Origin start to lose accuracy , this is due to the limitation of the number of decimal points used to calculate entity positions at that distance. Although it's not the norm to hatch at such distances, we have come up with a workaround if needed, simply click on the pattern that has lost it's definition and reset the hatch origin... see screenshot below. I will be reinstating the patterns I removed recently as we now know what is causing this...
The Installed AR-CONC.PAT does exactly the same thing and that's been around for years

New Updated Patterns now on Page 4 of this topic, The QCAD-LOGO was kindly fixed up by CVH , he edited 1 line of the code that was making 1 side of the pencil shift...dramatically [/size][/b]