Search found 9002 matches
- Wed Apr 08, 2015 11:50 am
- Forum: QCAD 'How Do I' Questions
- Topic: Copying drawings
- Replies: 4
- Views: 4792
Re: Copying drawings
how can I save the same layers that I did in 12" to 7mm to 1ft? Not sure I understand. Scaling should not do anything to your layers. Do you want to create a scaled copy on different layers or copy the scaled drawing to a new file or something similar? Also how do you get the measurement rulers in ...
- Wed Apr 08, 2015 7:44 am
- Forum: QCAD 'How Do I' Questions
- Topic: Can not get the "Ruler" on top and the side of board
- Replies: 5
- Views: 5984
Re: Can not get the "Ruler" on top and the side of board
You might have to close and re-open the drawing to make sure the graphics view is reinitialized with rulers.
- Mon Apr 06, 2015 7:29 pm
- Forum: QCAD Troubleshooting and Problems
- Topic: Incorrect Printing from Print Preview
- Replies: 6
- Views: 6638
Re: Incorrect Printing from Print Preview
Thanks for the details. There appears to be a problem with the printer driver or communication between our framework (Qt) and your printer or printer driver. Unfortunately, this is a problem that seems to be unique to your particular setup and is unlikely to be fixable on our end, so printing to PDF...
- Sat Apr 04, 2015 7:52 pm
- Forum: QCAD Troubleshooting and Problems
- Topic: Incorrect Printing from Print Preview
- Replies: 6
- Views: 6638
Re: Incorrect Printing from Print Preview
Thanks for the file. I'm unable to reproduce that problem here. I also created a PDF (uses the same logic as for printing) and it comes out just fine (see attached PDF). Perhaps you can try to print this PDF and check if that comes out right? Another possible problem could be the use of lineweight 0...
- Sat Apr 04, 2015 4:25 pm
- Forum: QCAD Troubleshooting and Problems
- Topic: Incorrect Printing from Print Preview
- Replies: 6
- Views: 6638
Re: Incorrect Printing from Print Preview
Please attach drawing file, thanks.
- Thu Apr 02, 2015 8:16 am
- Forum: QCAD 'How Do I' Questions
- Topic: Add a 5/8inch perimeter on imported images
- Replies: 1
- Views: 2950
Re: Add a 5/8inch perimeter on imported images
Could you attach an example drawing file? The exact steps depend a bit on the present situation. Thanks.
- Thu Apr 02, 2015 7:25 am
- Forum: QCAD Troubleshooting and Problems
- Topic: [solved] printing issue
- Replies: 9
- Views: 14290
Re: printing issue
luv_zen_13: My guess is that you have been adjusting the defaults for new drawings in application preferences instead of the preferences of the current drawing. Be sure to start the drawing preferences dialog with menu: Edit > Drawing Preferences Do NOT adjust drawing settings in Edit > Application ...
- Wed Apr 01, 2015 8:32 pm
- Forum: QCAD Troubleshooting and Problems
- Topic: [solved] printing issue
- Replies: 9
- Views: 14290
Re: printing issue
Thanks for your report. For all support requests, please: - indicate the operating system you are using and version thereof - indicate the exact version of QCAD you are using (see Help > About or QCAD > About QCAD) - attach original drawing files (DXF, DWG, ...) - include screenshots if appropriate ...
- Wed Apr 01, 2015 12:25 pm
- Forum: QCAD Troubleshooting and Problems
- Topic: QCAD crah
- Replies: 1
- Views: 2689
Re: QCAD crah
Thanks for your report. Please provide more details, so I can help you efficiently. - Does the crash occur if you only start QCAD and wait (don't start any tools, don't open any files). - Does the crash always occur if you try to open a file (try the example files included in your QCAD installation ...
- Wed Apr 01, 2015 7:25 am
- Forum: QCAD 'How Do I' Questions
- Topic: How to move Origin away from LH lower point of drawing?
- Replies: 5
- Views: 15083
Re: How to move Origin away from LH lower point of drawing?
Note that moving the absolute zero point (or origin) is exactly the same as moving your entire drawing: - Make sure all layers are visible - Select > Select All - Modify > Move / Copy - Set reference point at new position of absolute zero point - Click the current absolute zero point as target point...
- Fri Mar 27, 2015 9:18 am
- Forum: QCAD Suggestions and Feedback
- Topic: Layer list window setup
- Replies: 8
- Views: 14428
Re: Layer list window setup
I like the current layout because the eyes and locks are in one column respectively. It's also possible that more columns will be added in the future. IMHO, adding all these columns before the layer name would look very awkward for layer hierarchies because of the different indentations. What do you...
- Thu Mar 26, 2015 10:54 am
- Forum: QCAD 'How Do I' Questions
- Topic: [solved] Hidden Detail
- Replies: 2
- Views: 3592
Re: Hidden Detail
If I understand you correctly, you are looking for a way to control entity attributes (line color, line type, line weight).
Please refer to this thread in the tips and tricks section:
viewtopic.php?f=47&t=3202
Please refer to this thread in the tips and tricks section:
viewtopic.php?f=47&t=3202
- Thu Mar 26, 2015 8:46 am
- Forum: Introduce Yourself
- Topic: Hello from Western Colorado (USA)
- Replies: 2
- Views: 6103
Re: Hello from Western Colorado (USA)
Thanks for your introduction and insights. Welcome to the QCAD forum!
- Thu Mar 26, 2015 8:41 am
- Forum: QCAD 'How Do I' Questions
- Topic: How do I delete?
- Replies: 2
- Views: 4039
Re: How do I delete?
What you are asking is how to put QCAD back into 'neutral' mode after starting a tool. In QCAD, you can start a tool and when you're done working with it, you have to terminate it (QCAD does not know if you still want to draw more lines or not). To terminate a tool, you have several options: - Click...
- Wed Mar 25, 2015 4:34 pm
- Forum: QCAD Suggestions and Feedback
- Topic: [solved] status bar behavior
- Replies: 8
- Views: 13318
Re: Re:status bar behavior
Yes, this has been addressed for the next release.smf wrote:Would it be possible to have an option "never change the height of the status bar"?