|
1751 | QCAD (main) | Bug Report | Very Low | Can't open files from terminal | Closed | |
|
Task Description
I have file /home/test/test.dxf . When i try open file from terminal (qcad test.dxf), i have warning “File not found”. When i write full path (qcad /home/test/test.dxf), the file opens.
|
|
1760 | QCAD (main) | Bug Report | Very Low | Self-crossing polylines can't be cut twice at segment c ... | Closed | |
|
Task Description
Re-entering dividing problem from FS#1757
Divide the poly selecting near segment 1 at the segment crossing. > A new node is inserted on the crossing and made start and end node. Divide the poly again selecting near segment 2 at the segment crossing. > no division appears to be done.
One can’t divide the second segment at the crossing
Presumed intended behaviour like FS#1750
Regards
|
|
1762 | QCAD (main) | Bug Report | Very Low | Modify // .... selection of entities on locked layer al ... | Closed | |
|
Task Description
Not served with the degration to ‘Suggestion’ FS#1759 . Demanded closing FS#1759 & re-entered
Locking entities (by layer) to avoid selection,eg. nearby,very close by or on the same spot, does not have the intended influence.
Asumed wrong: - Modify DI - Modify B2 - Modify D3 - Modify MT These 4 need a single entity to be selected and selection of a locked entity is allowed.(=questionable) The action will allways leed to ‘not allowed’.(=correct)
Questionable: - Modify RM - Modify CH - Modify RN These 3 need a pair of entities. RM: Selection of a locked limiting entity is allowed (=questionable), enity to trim not.(=correct) The action will trim unlocked entities to the locked limiter.(=questionable) CH & RN: Selection of a pair of entities is allowed.(=questionable) Trimming if ‘trim’ is on will not occur because locked and leeds to ‘not allowed’.(=correct) The creation of the bevel or rounding on an active locked layer will not occur because locked and leeds to ‘not allowed’.(=correct) The creation, except for polyline segments (because locked themself), on an active unlocked layer will be done.(=correct)
Less severe but still questionable: (because these don’t necerally act on the locked entities themselves) - Modify OF - Modify OH - Modify SS OF: Selection of a locked base entity is allowed.(=questionable) The preview is casted only if the active layer is unlocked.(=correct) The creation is only done on an active unlocked layer.(=correct) OH: Selection of a locked base entity is allowed.(=questionable) Selection of point references from entities on locked layers is allowed.(=questionable) The preview is casted only if the active layer is unlocked.(=correct) The creation is only done on an active unlocked layer.(=correct) SS: Selection of point references from entities on locked layers is allowed.(=questionable) Strechting is only done for unlocked entities. (=correct)
|
|
1765 | QCAD (main) | Bug Report | Very Low | Errors with polyline offset | Closed | |
1 |
Task Description
Win 7 32 bit QCAD 3.20.1
Ofsset of a base-line with arcs results in massive ammount of errors. Most of them occur as a cluster of very tiny segments and are part of the offset. (zoom far in at the red circles) Mostly they occur where the offsetted arcs should merely be trimmend pairwise. Some occur as detached entities or as detached strings of entities very near the offset (strings not documented). Spooks occur at opposite site when base-line is not closed. 360° curls can occur with R = Offset. Null-entities may occur (not documented, hard to find and not able to copy).
The base-line is checked and sound and has mixed tangentially or not tangentially connected arcs. Offsetting the mother base-line of the base in the file has similar effect but not all and/or different ones. Also encountered with offseting polys from fonts. Used to define pocket paths for CNC. Detected because the CNC driver will not accept Self-crossers, Null-entities or open ends depending on the settings.
Work arround is to explode and select small entities but this does not solves the issues. 1) Choosing the tolerance large enough will detect small segments that should stay. 2) Recombining will generate new ones at the place where the main segments remain crossed. Cleaning up the paths is a daunting process with some thousand segments for several offsets.
I assume this has an infuence on the CAM part of QCAD too unless the offset method is different.
|
|
1767 | QCAD (main) | Bug Report | Very Low | Dimension Leader | Closed | |
|
Task Description
On print mode, the arrow not appear in the dimension
|
|
1795 | QCAD (main) | Bug Report | Very Low | Quit Menu Item disabled after opening preferences | Closed | |
|
Task Description
Quit Menu Item disabled after opening preferences.
System: OSX 10.13.6 Qcad version: 3.21.2.0
How to repeat:
Open QCad
Open preferences dialogue “QCad Pro → Preferences”
Close dialogue
The menu item “Quit QCad Pro” is now disabled. See attached screenshot
Repeatability: 100%
|
|
1798 | QCAD (main) | Bug Report | Very Low | Drawing Pref > Linetype > Scale of linetypes matches th ... | Closed | |
|
Task Description
“Drawing Preferences / General / Linetype / Scale of linetypes matches the scale of each viewport” is checked by default for new drawings, however the option is not applied until you open the “Drawing Preferences / General / Linetype” screen and click OK – no need to change anything, just opening the screen and clicking OK is sufficient.
|
|
1799 | QCAD/CAM | Bug Report | Very Low | Postprocessor: sign not forced for negative values roun ... | Closed | |
|
Task Description
formatValue returns “0” instead of “+0” for negative values that round up to 0 with the configured decimals.
|
|
1804 | QCAD (main) | Bug Report | Very Low | Application Preferences > Tool Settings: Filter for "Vi ... | Closed | |
|
Task Description
1. Search the Tool Settings for “View” and you will only find “Overlays” without the submenu information. 2. Check View manually without a search will provide the submenu information.
|
|
1806 | QCAD (main) | Bug Report | Very Low | Overlay Toolbar visibility in GUI not saved | Closed | |
|
Task Description
Switch “Overlay” Toolbar to visible below: View/Toolbars and Widgets/Toolbars/View/Overlays, place the Toolbar in GUI, restart QCAD and the Toolbar is back to invisible.
|
|
1899 | QCAD (main) | Bug Report | Very Low | View > Auto zoom: zoom to invisible entities in blocks | Closed | |
|
Task Description
Create and insert a block with entities on layer “0” and layer “1”.
Switch off layer “1”.
Auto zoom zooms to block boundary of all entities, including those on layer “1”.
See also: https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6336
|
|
1900 | QCAD (main) | Bug Report | Very Low | Remote shares initially not accessible. | Assigned | |
|
Task Description
My data files are stored on network shares (synology) with a GB link. QCAD Pro is run in Admin mode.
While in my Windows browser all remote shares are accessible (Green), in the QCAD file open menu they are initially shown as not accessible (Red). By accessing a specific drawing file in a remote share, the share will open and turn green.
Same behavior using ‘Open recent’. Always the message is given that the requested file does not exist, and the file is wiped from the ‘Recent Open’ list. Only if the share is first accessed through ‘Open’ with a random file, it will turn and a ‘recent open’ file for that share will open.
Drag and Drop from a remote share will never work.
|
|
1904 | QCAD (main) | Bug Report | Very Low | File > Bitmap Export: Non-plottable layers not exported | Closed | |
|
Task Description
File > Bitmap Export does not export non-plottable layers.
See also: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=6364
|
|
1905 | QCAD (main) | Bug Report | Very Low | View > Property Editor: Changing attribute of block cha... | Assigned | |
|
Task Description
See also: https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6367#p23947
|
|
1919 | QCAD (main) | Bug Report | Very Low | Wrong order XY(Z) for Ordinate Dimension in property ed ... | Closed | |
|
Task Description
Win7pro Qcad Pro 3.22.1.2
In property editor properties of an Ordinate Dimension
Without Show Z DefPoint is displayed in order YX?
With Show Z Origin is displayed in order XZY? DefPoint is displayed in order YZX? LeaderEndPoint is displayed in order ZXY?
Regards
|
|
1923 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polylines with Global/Local Widths and... | Assigned | |
1 |
Task Description
Win7pro 32bit Qcad 3.23.0
Andrew, The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.
In the attached drawing setting the Global Z of the inner poly to 5,10,...
The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly. It also affects the projected widths of the line inversely, but not by changing the widths properties.
Pritty rare combination! True. Qcad is 2D native! True.
Flatten will resolve this.
It is not a purely visual rendering fault, the poly will explode as such.
Maybe similar flaw as with uneven scaling blocks with arcs. https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703
Regards
|
|
1932 | QCAD (main) | Bug Report | Very Low | Check for update fails to discover new version | Closed | |
|
Task Description
“Help→Check for QCAD Pro Updates” fails to discover new version. Tested on OSX and Linux versions.
|
|
1974 | QCAD (main) | Bug Report | Very Low | File > Print Preview: Cannot move paper in new drawing | Unconfirmed | |
|
Task Description
Yesterday I set up a Windows 64 bit install of QCAD Pro which shows the same bug I have been seeing for a while in the Community linux git repo.
Create a new drawing and then go to “Print preview”. Enable “Move paper postion”, the cursor changes to the hand icon, but the paper position is unable to be moved. Only by saving the drawing, exiting the program, restarting and reopening the drawing, will the “Move paper postion” function correctly.
Affected versions tested:
Windows 64bit installer download, as of yesterday. Linux 64bit build from git, about 20minutes ago.
For what it’s worth, this bug is not present in this previous git checkout:
Version: 3.21.1.0 (3.21.1) Internet: QCAD.org Build Date: Jul 2 2018 Revision:
Qt Version: 5.7.0 Architecture: x86_64 Compiler: gcc 6.3.1
Thanks for a great product.
|
|
2029 | QCAD (main) | Bug Report | Very Low | Block order issue within drawing exchange between CE an ... | Closed | |
|
Task Description
If I create a dxf in Pro and open it in CE (or vice versa) the block order can change strange and a new Layout Block is occasionally added. Looks like dxf version (R15 etc.) doesn’t matters.
Versions: QCAD Pro 3.24.2.0 QCAD CE 3.24.0.0
|
|
2048 | QCAD (main) | Bug Report | Very Low | Move / Copy to current layer fails when reference point... | Assigned | |
|
Task Description
QCAD 3.24.2 / macOS x86_64 10.14.6
Starting with empty doc: 1. Draw any object (e.g. a rectangle) on layer 0. 2. Create new layer (”1”) with color, say yellow. 3. Select new layer 4. Select new object 5. Modify → Move / Copy 6. Click reference point 7. Click target point same as reference point 8. In “Move / Copy Options” dialog, select “Delete Original” and check “Use current layer and attributes.” Click OK.
The moved object stays on the layer it was previously on. Using “Move / Copy” as a quick way to move a selection between layers is not useful even though it appears to be the recommended way in a Google search.
Note: if “Keep Original” is selected instead, the copied object is placed on the current layer and the original object remains on its layer, as expected.
Note: if the target point is different from the reference point, the moved object is placed on the current layer as expected.
There are other workarounds too, cut / paste with “To current layer” checked seems to work, as does chaging the layer in the Properties Editor.
|
|
2050 | QCAD Community Edition | Bug Report | Very Low | FlexPainter dosen't work | Closed | |
|
Task Description
FlexPainter works in the Pro version of QCad but not in the Comunity one. If it’s not supposed to works in the latter, maybe, it would be better to remove it from the menu (Misc > Script Examples > Mathematics).
|
|
2068 | QCAD Community Edition | Bug Report | Very Low | Non-english text in upper/lower index becomes UTF code | Assigned | |
|
Task Description
How to reproduce.
1. Create a text field with some non-english words in the upper index. (see attached pic1.png) 2. Save the project and close QCAD. 3. Run QCAD and open same project. 4. Now upper/lower indexed text becomes not human readable UTF codes. (see attached pic2.png)
Tried different fonts - doesn’t help.
Linux ntb-kirill 3.10.0-1062.12.1.el7.x86_64 #1 SMP Tue Feb 4 23:02:59 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux CentOS Linux release 7.7.1908 (Core)
|
|
2085 | QCAD (main) | Bug Report | Very Low | Drag and drop: moving single polyline vertex moves also ... | Closed | |
|
Task Description
See the steps to reproduce in the attached drawing.
|
|
2088 | QCAD (main) | Bug Report | Very Low | column headers of the "General: tool settings " resize... | Assigned | |
|
Task Description
Open QCAD and the application preferences. In the section “General: tool settings " you can resize the columns: Menu, Shortcuts etc. The problem is that it is not intuitive. The first divider is not selectable and the second moves the first, only backwards.
|
|
2097 | QCAD (main) | Bug Report | Very Low | Very hard to snap to baseline reference point of dimens... | Assigned | |
|
Task Description
With default autosnap settings reference points included I find it very hard to snap to the baseline reference points of a dimension. I manage to do it by setting snap to reference point only and zoom out till I see the entire dimension element.
|
|
2098 | QCAD (main) | Bug Report | Very Low | Offset will pick up hidden blocks while using it in a l... | Assigned | |
1 |
Task Description
When I’m drawing inside a layout block the offset tool picks up lines from blocks that are hidden. It is not happening with all the block.
|
|
2144 | QCAD (main) | Bug Report | Very Low | Draw > Viewport > Add Viewport: Custom hatch pattern no ... | Closed | |
|
Task Description
QCAD Professional
Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Orphan Hatches (without a *.pat file installed) are no longer visible in a viewport
Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7830 Original topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7340 File: #2 https://qcad.org/bugtracker/index.php?do=details&task_id=2063
Regards, CVH
|
|
2151 | QCAD (main) | Bug Report | Very Low | Update viewport on Layout after Layer property change | Closed | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
With the attached file: Viewing Layout1 Changing ON/OFF or Frozen state of layers in the Layer List
The view doesn’t update immediate. Selecting an entity: Yes After QQ Yes Switching to another Application and reverting the focus back to QCAD: Yes Using zoom / pan or the Zoom functions: No Changing the display modes: Yes Starting an action: No
|
|
2155 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polyline Arcs with Width = 2R | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Most likely not related to the QCAD version, rather an old sore.
File included Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7889#p30803 Confirmed by ‘cccplex’ Linux ‘Latest Ubuntu’
Polyline arcs with Width = 2R render as circle segments rather than circle sectors. As Non-reversed arcs these don’t explode. As reversed arc these explode to a single arc rather than a circle sector contour.
There is also still the faulty rendering with Z not zero https://qcad.org/bugtracker/index.php?do=details&task_id=1923
Regards, CVH
|
|
2175 | QCAD (main) | Bug Report | Very Low | Edit > Application Preferences > Draw > Text: Uncheck a ... | Closed | |
|
Task Description
In the Application Preferences>Draw>Text dialog, when first opened, the Uncheck all and Check all buttons are not disabled if the Show font preview in font controls check box is checked. If you click on the Use reduced selection of fonts check box twice the buttons become disabled.
|
|
2176 | QCAD (main) | Bug Report | Very Low | Modify > Break out Manual: relevance of order of click ... | Assigned | |
1 |
Task Description
QCAD Professional Windows 7; Win installer 32 bit Version: 3.25.2.7 (3.25.2.7) Internet: QCAD.org Build Date: Dec 16 2020 Revision: e06f230 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Forum Topic: https://qcad.org/rsforum/viewtopic.php?t=7988 File included. I have no intention to make 48 separate reports.
CVH
|
|
2193 | Command line tools | Bug Report | Very Low | dwg2csv retains the last encountered custom properties | Closed | |
|
Task Description
QCAD Professional Win installer 32 bit Version: 3.25.2.13 (3.25.2.13) Internet: QCAD.org Build Date: Feb 12 2021 Revision: cad2d36 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Andrew, While enhancing DrawFromCSV: Forum Link. I had a peek at the new command line tool: dwg2csv
I would never come up with 115 columns. That wouldn’t be efficient to generate entities from. Although this way it is very complete and one could use specific lists to filter. One downside is that the ‘-list’ switch return is far too vast for the windows command line.
Remarked that: Only the first alphabetically custom property is listed under: QCAD:Line & QCAD:Reference (columns 114-115). And that the last encountered is persistent for all entities that follows.
Maybe this originates from a multiple entity selection ... ... what also retains the last encountered custom properties in the property editor. Should I add a seperate task for that?
Also had an exception thrown: Debug: dropped global XDATA (no res buf): “ViewportCenter”. Discarted that as this very basic test drawing hasn’t even a Viewport.
Regards, CVH
Added: Snippet from DrawFromCSV code (merely a test case)
CSVcomma/semicolon
Offset;50;50
Point;39,789355;-0,815325;+[Custom;Reference:101];
Point;38,49526;4,014304;+[Custom;Reference:102;Line:56]
The two points, and only those two points, are casted with custom properties QCAD|Reference|101 QCAD|Reference|102 & QCAD|Line|56
Added: The dxf file Added: The csv file (change to the comma/semicolon style)
|
|
2194 | QCAD (main) | Bug Report | Very Low | Multiple selection of entities with custom properties d ... | Closed | |
1 |
Task Description
QCAD Professional Win7 installer 32 bit Version: 3.25.2.13 (3.25.2.13) Internet: QCAD.org Build Date: Feb 12 2021 Revision: cad2d36 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
In the file provided one would expect *VARIES* in the property editor under custom properties when selecting 2 or more entities. The key list is reduced to what keys are common to the multiple selection. (Here 3) The values displayed are inconsistent depending the selection.
Select All » 3 custom properties of line 3 Select the 3 vertical » 3 custom properties of line 2 Select the first vertical and the diagonal » 3 custom properties of line 1 Select all but the first vertical » 3 custom properties of line 3 And so on ...
Regards, CVH
|
|
2212 | QCAD (main) | Bug Report | Very Low | Cannot change f5 shortcut in preferences. | Closed | |
|
Task Description
I’d like to change the f5 shortcut from rotate counter-clockwise to move/copy.
I started with a fresh QCAD3.conf
In the preferences window: general: tool settings
First time I remove f5 from rotate counter-clockwise qcad crashes. Second run it seems to work. I add the shortcut f5 to move/copy and restart. The shortcut doesn’t work. And tool settings has a notice that there are conflicts. When I change it to f3 it works.
btw the shortcut column don’t show any shortcuts. See screenshot.
|
|
2218 | ECMAScript | Bug Report | Very Low | RPolyline.appendVertex() doesn't default to width = zer ... | Closed | |
1 |
Task Description
When I use poly.appendVertex(vector, bulge) the polyline is finally created with NAN widths
This, while the signature explains that bulge, width1 and width2 default to zero. https://www.qcad.org/doc/qcad/latest/developer/class_r_polyline_entity.html#a9ee706e50d6cc267fc84a85b7c81d5e6
Regards, CVH
|
|
2223 | QCAD (main) | Bug Report | Very Low | Block > Insert Block: duplicate entries in attributes c ... | Closed | |
|
Task Description
Insert block with multiple instances of the same attribute definition (same tag). Attributes combo box shows multiple entries for the same attribute.
|
|
2225 | QCAD (main) | Bug Report | Very Low | Filenames containing an ampersand do not render correct ... | Closed | |
|
Task Description
If a file is opened whose filename contains an ampersand, the filename will be rendered correctly in the application titlebar, but the tab bar and the Window menu will not display the ampersand.
If, however, the ‘alt’ key is pressed, the ampersand will result in an underscore appearing beneath the character immediately following it in the filename string. This applies both to the titlebar and the Window menu.
Interestingly, this can be “exploited” by a user to quickly switch between tabs by pressing ‘alt’ and the character which follows the ampersand simultaneously. Likewise, a user can swap between windows using the Window menu in a similar fashion, by first pressing Alt+W, then Alt and the same key as before.
The expected result is that the ampersand is rendered, the underscore is not rendered, and the ‘alt’ key shortcuts don’t work.
It would appear that this is a simple case of failing to properly escape the ampersand in filenames before passing the filename string to various Qt methods.
|
|
2248 | QCAD (main) | Bug Report | Very Low | Themes: east and west dock widget tabs facing the wrong... | Assigned | |
1 |
Task Description
Hi Andrew
In QcadCAM when using the new Themes or User Created Themes the Layer and Block Tabs Appear to be reversed in East and West Positions. I have discussed this with forum user PeteVick and he cannot reproduce this behavior in Qcad Pro... he suggested submitting this bug report. I didn’t notice this until he pointed it out and don’t expect it to be high on your list of things to do..
Best Regards John Hyslop PS We are both using Linux Mint 20.1 (64bit) which is based on Ubuntu
|
|
2263 | QCAD (main) | Bug Report | Very Low | dwg2svg -min-lineweight option parsing broken | Closed | |
|
Task Description
The parsing for the -min-lineweight option of dwg2svg is broken, only -w or the undocumented -minlineweight options work.
This is due to a typo in the Dwg2Svg.js script around line 225:
properties["minLineweight"] = getArgument(args, "-w", "-min-lineweight");
if (isNull(properties["minlineweight"])) {
properties["minLineweight"] = getArgument(args, "-w", "-minlineweight");
}
This should be:
properties["minLineweight"] = getArgument(args, "-w", "-min-lineweight");
if (isNull(properties["minLineweight"])) {
properties["minLineweight"] = getArgument(args, "-w", "-minlineweight");
}
Note the case minlineweight vs minLineweight.
This has the consequence that the value parsed form -min-lineweight is always replaced with the value from -minlineweight, which is usually undefined.
Since the short option -w is parsed in both cases, it is not affected from the bug.
|
|
2290 | QCAD (main) | Bug Report | Very Low | loading the Drawing Preferences using enter, using ente... | Assigned | |
|
Task Description
I use CTRL + I to pull up drawing preferences. Upon changing the dimension settings quickly and closing it normally by pressing enter it closes. But if i go to the next tab (drawing tab) then press enter to load it up quickly instead of pressing CTRL + I. Upon changing the dimensions settings and pressing enter to close it, it won’t close but instead flash and i have to keep pressing enter and eventually it closes.
I think this is a bug.
I have the Pro Version
|
|
2298 | QCAD (main) | Bug Report | Very Low | Centroid mismatch | Closed | |
1 |
Task Description
Please refer to: https://www.qcad.org/rsforum/viewtopic.php?f=32&p=35080#p35080
Can this be implemented as a GUI metod? Two feature requests: See FS#883 , FS#1449
Regards, CVH
|
|
2302 | QCAD (main) | Bug Report | Very Low | polygon.getSelfIntersectionPoints(tol) returns 3th inva... | Assigned | |
1 |
Task Description
Windows 7 pro 32 bit msi-Installer Version: 3.26.4.5 (3.26.4.5) Internet: QCAD.org Build Date: Jul 20 2021 Revision: e596276 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Andrew,
In the attached dxf: Besides that it is clear that duplicate vectors are not filtered ... Where a segment is crossing in another node a non valid node is returned as self-intersection point. Seems to be unrelated to CW/CCW or tolerance.
Where 2 nodes coexists 4 duplicate vectors are returned.
Regards, CVH
|
|
2328 | QCAD (main) | Bug Report | Very Low | drop down, using keyboard | Assigned | |
|
Task Description
Minor issue! When using keyboard to initiate the dropdown menus. I noticed the ALT “D” does not cycle through the headings Draw & Dimension in the same way. ALT “M” cycles though Modify & Misc or ALT “S” cycles though Select & Snap. User Name: StanTibbs E-mail: [email protected]
|
|
2350 | QCAD (main) | Bug Report | Very Low | Quick Modify - Icons Missing From Toolbar | Closed | |
|
Task Description
Hi Andrew
The Icons are missing on the Quick Modify Toolbar..
Cheers John
QCAD/CAM Version: 3.27.1.0 (3.27.1) QCAD.org Build Date: Dec 13 2021 Revision: 2726424 Qt Version: 5.8.0 Architecture: x86_64 Compiler: gcc 4.8.1
PS Also missing on windows version 3.27.1 See Forum Post below. https://www.qcad.org/rsforum/viewtopic.php?f=33&t=9220
|
|
2357 | QCAD (main) | Bug Report | Very Low | Reference points not cleared when deleting selection | Closed | |
|
Task Description
See also: https://qcad.org/rsforum/viewtopic.php?f=89&t=9274
|
|
2415 | QCAD (main) | Bug Report | Very Low | Issues with OffsetBothSides | Assigned | |
1 |
Task Description
Andrew,
I can’t find any documentation concerning OffsetBothSides under Misc .. Modify. It is not listed in the QCAD features nor in the changelog.
There was a Feature Request FS#1130 for this, I think you might want to close that as being implemented.
The tool asks for a Line, Arc, Circle, Ellipse, Spline or Polyline. It also seems to act on shapes that can be exploded to such entities like Text, Dimension and Hatch entities.
There may be many ‘Result loop not closed’ or ‘No offsets possible’ warnings when hovering over entities on a drawing. The preview may be partially, one or two sided and even two sided partially and closed with semi-circles.
I only successfully created a dual offset for open Splines, open or logically open Polylines. All other attempts result in a single offset at the indicated side.
There are the usual exceptions for Polylines with arc-segments but that is related to small arc segments and being tangentially connected. Only tested it on a Win7 platform. I don’t suspect that version 3.27.8 includes a fix for that ...
Regards, CVH
|
|
2439 | QCAD (main) | Bug Report | Very Low | Selecting Overlapping Lines | Closed | |
|
Task Description
OS: Linux, Mint 20 Cinnamon 4.6.7, QCAD 3.27.8
According to: https://www.qcad.ch/rsforum/viewtopic.php?t=3944 it should be possible to do Alt+Click on overlapping lines to bring up a small context menu to allow resolving the selection ambiguity. In the current version of QCAD I find it necessary to do Ctrl+Alt+Click.
|
|
2440 | QCAD (main) | Bug Report | Very Low | Hatch from Segments > False positives open loop warning... | Assigned | |
1 |
Task Description
Andrew,
Most probably not related to OS or QCAD version.
When hatching an area with Hatch from Segments (HS) there might be false positive warnings on open loops. It seems that this is related to the orientation of the indicated segments and the order of selection. The real problematic position is not always the first that is reported. Loop count is increased even if it is a single loop.
Included a basic test drawing to replicate these. Further details to replicate the issue are in the file.
Regards, CVH
|
|
2443 | QCAD (main) | Bug Report | Very Low | Modify > ‘Draw Order’ sub-menu missing | Closed | |
1 |
Task Description
Andrew,
I don’t seem to be able to locate the ‘Draw Order’ sub-menu of the Modify menu. Reported version 3.27.6 and 3.27.8 (I use them side by side) Tested on Win7 32 bit and Win10 64 bit.
I am aware that MF & MB were relocated out of the Modify menu. Two additional PRO tools were added and all four were listed in a sub-menu. (MO: version 3.21.3; MC: information missing in changelog)
MF, MB, MO and MC are displayed in the Modify Toolbar, in the Modification Tools panel and in the Tool Matrix. This is even more curious because DrawOrder.init() only initiates DrawOrder.getMenu(); All three DrawOrder.getToolBar() & DrawOrder.getCadToolBarPanel() & DrawOrder.getToolMatrixPanel() are ruled out.
DrawOrder.getCadToolBarPanel() lists WJ as shortcut QKeySequence but that will bring up the Projections Tool Panel.
In the QCAD Reference Manual (menu Help > Reference Manual) the ‘Draw Order’ icon list is only the Modifying Tools icon. For all four the tools the manual list up: Menu: Modify > Draw Order > ...
Under App.Prefs. > General > Tool Settings MF and MB are listed but not in a sub-menu like for example “Detection“. Seemingly under Modify but they remain visible when Modify is collapsed. MC and MO are listed lower than Help when this is collapsed.
I thought I understood how to implement menus and tools. All this makes me doubt whether I had understood it in its entirety. Could you elaborate in a few words why the menu fails but the Toolbar and Panels work even when these are excluded ...
Regards, CVH
|
|
2461 | dxflib | Bug Report | Very Low | ASCII Control characters not handled correctly in Commu... | Assigned | |
|
Task Description
I see the following problem: When I open a particular DXF file in the Professional Trial version 3.27.9.0 on macOS, “^I” in text fields is expanded to whitespace. When I open the same DXF file in the Community Edition 3.27.9.0 on NetBSD/x86_64 (installed from pkgsrc), “^I” in text fields is visible as “^I”.
|