QCAD Bugtracker

1. select hatch
2. click “+” in property editor to move selection to new layer
3. enter new layer name
4. OK

Tool that trigger long operations (e.g. rotate with complex entities, angle 1, 359 copies) can sometimes not be terminated after the operation is finished.

Crash when launching QCAD with -quit option:

./qcad -quit

See RDwgEllipseImporter::import

Crash in QVariantAnimation.

Potential fix: configure Qt with -D QT_NO_ANIMATION

TODO: check on other platforms

Hatch fails with more than one full-ellipse islands

See fs511.dxf

“Null Object ID” exception when saving a previously loaded file.

File: “fs515.dwg”

Dependency possibly not needed?

See forum thread:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=8&t=1902

www.qcad.org

See also:
http://www.qcad.org/rsforum/viewtopic.php?f=32&t=1945

Centers based on size of entire drawing including invisible layers.
Should only center based on visible layers.

Most likely a timeout issue if the machine is very busy:
- Explorer launches QCAD when a file is double-clicked
- QCAD checks if another instance of QCAD is already running by trying to contact the other instance. This may time out if the operating system is very busy or QCAD has not been used for a while and needs to wake up first.

See also:
http://www.qcad.org/rsforum/viewtopic.php?f=33&t=1980

Line tangent to ellipse with start point on the minor axis of the ellipse produces wrong result.

- Remove unused option ‘show bounding box’ - Fix ‘show page borders’ (should be ‘show paper borders’)

In version 2.2.2.0 when unit mil is selected the grid choices are auto, 0.01, 0.1, 1, 10
In version 3 when mil is selected the grid units are 1/128, 1/64, 1/32 ...... etc. binary.
This needs correction. I use the grid a lot when I draw so this is a high priority for me.

Split entities: start angle must be entered in degrees * 1rad (converted from degrees to rad twice)

See:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=32&t=1909

CAD font styles not saved (except standard)

Hatches using user added hatch patterns cannot be saved.

OpenDesign error message: “Bad name for Hatch pattern”

See:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=11&t=2099

Customer reports that TTF called “Magneto” is not shown properly.

Affects drawings in inch with hatch patterns ISO03W100 and ISO03W100A

OpenSuSE 12.2: the grid info display is not displayed:
http://www.qcad.org/rsforum/viewtopic.php?f=32&t=2178&view=unread#unread

Menu View - Toolbars shows only a few of the available toolbars.

See forum at:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=11&t=2249&view=unread#unread

Make sure that block references of hidden blocks cannot be selected.

Steps to reproduce:
- Start QCAD
- Switch to another application by clicking on its title bar
- Switch back to QCAD by clicking on its title bar
- Without any further clicks, start panning using the middle mouse button (panning is performed but graphics view does not update)

Alternative:
- Start QCAD
- Draw a line
- Start line parallel tool
- Switch to another application by clicking on its title bar
- Switch back to QCAD by clicking on its title bar
- Without any further clicks, try placing the parallel (no preview is shown, a click will place the parallel, graphics view is often updated much later)

To reproduce:
- Create a part library item with file name “Test1 .dxf” (note the space at the end of the base name)
- Insert this part library item into a blank drawing
- Try to save the drawing
- Error “Invalid Symbol Table Name” occurs

See fs731.dxf

Command line switch -always-load-scripts has no effect.

Modify divide moves split entities to new layer if circle or full ellipse is divided.

The spacing of the isometric grid is not updated correctly, if the grid spacing is not set to ‘auto’ but fixed values and the isometric grid is switched on using the menu or tool bars:
- Set grid to orthogonal grid, spacing fixed: 1/1
- Set meta grid to orthogonal grid, spacing fixed: 10/10
- Switch to isometric grid using menu or tool bar buttons

Splines produced by Illustrator are not correctly imported or displayed.

See:
http://www.qcad.org/rsforum/viewtopic.php?f=11&t=2344

Intuos Mouse (moving around on the Intuos Tablet)

• does work for drawing and marking with the left button on the drawing area
• does work for zooming in and out with the middle-button wheel
• does work for calling up context menus with the right button on the menu bar and the layer list window
• does not work with the left button for actually clicking any menu item (Edit, View, ..) nor action icon on the top nor the left (e.g., draw lines, measure, zoom, undo, save, ..) nor the layer window (e.g., toggle visible, lock layer) nor the property editor.

Wacom mouse model: ZC-100-01
win7-64 sp1

- Draw ellipse
- Fill ellipse (solid or hatch)
- Rotate ellipse and filling
- Undo

→ Angle of ellipse shaped fill is not undone.

Other hatch boundary elements that break or cannot be undone:
- splines from fit points
- arcs (when only one point is moved, e.g. stretch)
- circles (when radius changes, e.g. scale, position changes)
- ellipses (when major point changes)

Info tools show too many ticks which leads to slow down / crash.

Imported splines which typically represent lines, circles or arcs (explicit knot vector given) are sometimes wrongly identified as invalid by the OpenNURBS library.
This results in splines that are loaded and displayed correctly but are not selectable.

dxflib 3.1 saves the text style name as style font in text styles.

Editing text in QCAD leads to line feeds that are incompatible with some other products (\p instead of \P).

Conversion of certain files leads to crashes (segmentation fault).

See:
http://www.qcad.org/rsforum/viewtopic.php?f=33&t=2501

Polylines that are stored with vertices as separate entities in DXF are not read by QCAD.
See:
http://www.qcad.org/rsforum/posting.php?mode=reply&f=33&t=2531

Stretching hatch entities results in broken hatches.
Regression introduced in QCAD 3.1.5, bug still present in 3.2.2.

Action to move paper in print preview does not properly terminate on right-click (paper can still be moved after right-click)

Exploding a block with attributes results in wrong exploded text (tag instead of value).

Text with é turns into È.

See:
http://www.qcad.org/rsforum/viewtopic.php?f=89&t=2548